储油罐核心包含：（1）与第三方通风管道对焊接入的第 第一道环向线连接管的坡口面;（2）英制外螺纹接入的第 一英制外螺纹线连接管激光切割端面;（3）活套活套法兰联接的第 一种活套活套法兰封好性面;（4）专用箱联接件还是管联接的第 一种封好性面；（5）非压力强度开关元件与化工储罐的联接焊接。储存罐基座中的注意耐压元器件封装包涵罐顶、罐壁、罐底、公称网套直径多于或值为250 mm的接手和管卡箍。储存罐的安全防护卫生卫生附近，包涵同时配置在储存罐上的安全防护卫生卫生阀/感受不到阀、药液泄压阀、急救立即切断配置、安全防护卫生卫生连索配置、气压表、液位计、温差计、阻火器等。过热蒸汽卧式储罐罐底板一切正常情况发生下，罐底板仅起着传输石油和罐体脂率力的能力，故似的底板强度在5mm上述。底板由板材安装熔接而成。其长相面与知识基础碰触，轻松反潮，内表层又总是碰触石油中的形成的含水量和杂质残渣，以至于底板轻松遭受到金属腐蚀，后加之很难体检和修理汽车，以至于需要罐底板熔接后没有渗漏，防腐施工处理好。卧式贮罐贮罐罐壁形式特征 罐壁是由几层的圈板組裝而成，第一层圈板上的垂直于焊道均主要包括嫁接，圈板与圈板两者的环向焊道则基于用需要都可以嫁接，也能钢筋焊接。上、下圈板两者的排顺方式有交互技术式、套筒式、嫁接式和分层式。嫁接焊道在铝合金板规格厚薄相当或少于6mm时，平常应开坡口，铝合金板规格钢筋焊接口处的非常平常为6~8倍板厚，常取35~60mm。The tank body includes: (1) the groove surface of the first circumferential joint welded with the external pipeline; (2) The end face of the first threaded joint of the threaded connection;(3) The first flange sealing surface of flange connection; (4) The first sealing surface connected by special connectors or pipe fittings; (5) Connection weld between non pressure bearing components and storage tank.The main pressure bearing components in the tank body include tank top, tank wall, tank bottom, connecting pipe and pipe flange with nominal diameter greater than or equal to 250 mm. The safety accessories of the storage tank include the safety valve/breather valve, liquid pressure relief valve, emergency cut-off device, safety interlock device, pressure gauge, liquid level gauge, thermometer, flame arrester, etc. directly installed on the storage tank.Bottom plate of atmospheric storage tankUnder normal circumstances, the bottom plate of the tank only plays the role of transferring oil products and tank gravity, so the thickness of the bottom plate is generally more than 5 mm. The base plate is laid and welded by steel plates. Its outer surface is in contact with the foundation, which is easy to get damp, and its inner surface is often in contact with the water and impurities deposited in the oil, so the bottom plate is easy to be corroded. In addition, it is not easy to check and repair, so it is required that the tank bottom plate should be free of leakage after welding, and the anti-corrosion measures should be good.Structure characteristics of atmospheric tank wallThe tank wall is assembled by several layers of ring plates. The vertical welds on each layer of ring plates are butt welded. The circumferential welds between the ring plates can be butt welded or overlapped according to the use requirements. The arrangement modes between the upper and lower ring plates are interactive, sleeve type, butt joint type and hybrid type. When the thickness of butt weld steel plate is equal to or greater than 6mm, the groove shall be generally made. The height of steel plate lap joint is generally 6-8 times the plate thickness, usually taking 35-60mm.

上一条:油罐

下一条:油罐